Sclairpipe® Solid-wall (SW) Polyethylene (HDPE) Pipe.
Manufactured by Infra Pipe Solutions Ltd.
Brand: Sclairpipe® Solid-wall
Sclairpipe® SW HDPE pipe are manufactured in diameters from 19mm (3/4") to 1600mm OD in 10 different pressure classes: DR32.5 (64 psi), DR26 (80 psi), DR21 (100 psi), DR17 (100 psi), DR15.5 (110 psi), DR13.5 (128 psi), DR 13.5 (160 psi) DR11 (200 psi), DR9 (250 psi), DR7.3 (317 psi), DR6.3 (300 psi). Tough, lightweight, smooth inner surface, corrosion/abrasion resistant, heat-fusible (trenchless / HDD), flexible, solid-wall PE piping system. For more information go to www.uponor.ca
| Prequalification Lists: |
|
Regional Municipality of Durham -
4.70.62.64
- High Density Polyethylene (HDPE)
(PDF)
|
|
Regional Municipality of Halton -
4.70.62.64
- Polyethylene (HDPE)
(PDF)
|
|
City of Vaughan -
4.70.62.64
- High Density Polyethylene (HDPE)
(PDF)
|
|
-
ASTM International
-
ASTM D1238-10 - Flow Rates of Thermoplastics by Extrusion Plastometer
-
ASTM D1248-12 - Polyethylene Plastics Extrusion Materials For Wire and Cable
-
ASTM D1505-10 - Density of Plastics by the Density-Gradient Technique
-
ASTM D1598-02(2009) - Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
-
ASTM D1599-14e1 - Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings
-
ASTM D1693-12 - Environmental Stress-Cracking of Ethylene Plastics
-
ASTM D2290-12 - Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
-
ASTM D2321-14e1 - Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
-
ASTM D2513-13 - Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
-
ASTM D2657-07 - Heat Fusion Joining of Polyolefin Pipe and Fittings
-
ASTM D2837-13e1 - Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
-
ASTM D3035-15 - Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
-
ASTM D3350-14 - Polyethylene Plastics Pipe and Fittings Materials
-
ASTM D543-06 - Evaluating the Resistance of Plastics to Chemical Reagents
-
ASTM D638-14 - Tensile Properties of Plastics
-
ASTM D792-08 - Density and Specific Gravity (Relative Density) of Plastics by Displacement
-
ASTM F714-13 - Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter
-
Canadian Standards Association
-
Other Standards
-
ASME B16.1-2010 - Gray Iron Pipe Flanges and Flanged Fittings
-
AWWA C901-08 - Polyethylene (PE) Pressure Pipe and Tubing, ½ in. (13 mm) Through 3 in. (76 mm), for Water Service
-
ISO 9001:2000 - Quality management systems -- Requirements
-
TR31 - Underground Installation of Polyolefin Pipe
-
Manufacturer
-
Infra Pipe Solutions Ltd.
